TY - GEN
T1 - Preliminary doe analysis and control of mapping procedure for a turbocharger on an engine gas-stand
AU - Avola, Calogero
AU - Dimitriou, Pavlos
AU - Burke, Richard
AU - Copeland, Colin
N1 - Publisher Copyright:
© Copyright 2016 by ASME.
PY - 2016
Y1 - 2016
N2 - The use of turbochargers on both gasoline and diesel engines is started to become a common strategy to comply with stringent limits on CO2. The main action towards lowering fuel consumption of powertrains is achieved by reduction of engine size and number of cylinders, annexed to the lower friction. However, this is directly linked to the worsening of deliverable output power under the natural aspirated configuration. Therefore, turbocharging is often adopted to overcome this problem where useful energy contained in the exhaust gasses is used to increase the air density at the intake. The increase in power from a natural aspirated configuration is a direct consequence of higher fuel quantity to be injected. In order to pursue a systematic evaluation of the powertrain system, engine, turbochargers and auxiliary components are included into 1D models. Several conditions can be simulated without the need of an extensive test plan. In 1D software like Ricardo Wave, turbochargers performance are imposed as input. These are previously measured in appropriate turbocharger gas-stand where hot or cold air is blown through the turbine while load on compressor is controlled by adjusting a back pressure valve. Compressor and turbine maps are generated for constant speed lines which are corrected for total temperature. Pressure ratio, mass flow and isentropic efficiency are also monitored as parameters to characterize performance maps of turbomachinery. In gas-stands, steady flow conditions are imposed at compressor and turbine. However, in turbocharged engines, pulsating flows induced by the engine valvetrain disturb continuously turbocharger conditions during the engine cycle. In fact, the effects that the conditions of the engine air-path could have on the turbocharger operations are excluded from the system modelling. In this study, an appropriate engine gas-stand has been developed in order to improve the accuracy on estimating the turbine extraction power in 1D powertrain simulations. In addition, future analyses on turbocharger transient operations could be investigated. The compressor outlet has been disconnected from the 2.2L Diesel engine intake so that the load on turbocharger and engine can be independently controlled. In order to extend the engine capability in delivering mass flow and pressure at the turbine inlet, an external boost rig has been installed with the capability to control pressure, mass flow and temperature at the engine intake. In a first instance, a 1D model of the system including turbomachinery, Diesel engine and boost rig has been developed using the commercial platform Ricardo Wave. In this way, a preliminary DoE study of the entire system has been performed in order to evaluate the effects of parameters and actuators on the turbocharger operations. Additionally, the control of the rig has been tested by confirming the previous DoE study. Approaches to create turbochargers maps are shown. Last section of the paper focuses on turbine pulsations and the interpretation of efficiency calculated in experiments and simulations.
AB - The use of turbochargers on both gasoline and diesel engines is started to become a common strategy to comply with stringent limits on CO2. The main action towards lowering fuel consumption of powertrains is achieved by reduction of engine size and number of cylinders, annexed to the lower friction. However, this is directly linked to the worsening of deliverable output power under the natural aspirated configuration. Therefore, turbocharging is often adopted to overcome this problem where useful energy contained in the exhaust gasses is used to increase the air density at the intake. The increase in power from a natural aspirated configuration is a direct consequence of higher fuel quantity to be injected. In order to pursue a systematic evaluation of the powertrain system, engine, turbochargers and auxiliary components are included into 1D models. Several conditions can be simulated without the need of an extensive test plan. In 1D software like Ricardo Wave, turbochargers performance are imposed as input. These are previously measured in appropriate turbocharger gas-stand where hot or cold air is blown through the turbine while load on compressor is controlled by adjusting a back pressure valve. Compressor and turbine maps are generated for constant speed lines which are corrected for total temperature. Pressure ratio, mass flow and isentropic efficiency are also monitored as parameters to characterize performance maps of turbomachinery. In gas-stands, steady flow conditions are imposed at compressor and turbine. However, in turbocharged engines, pulsating flows induced by the engine valvetrain disturb continuously turbocharger conditions during the engine cycle. In fact, the effects that the conditions of the engine air-path could have on the turbocharger operations are excluded from the system modelling. In this study, an appropriate engine gas-stand has been developed in order to improve the accuracy on estimating the turbine extraction power in 1D powertrain simulations. In addition, future analyses on turbocharger transient operations could be investigated. The compressor outlet has been disconnected from the 2.2L Diesel engine intake so that the load on turbocharger and engine can be independently controlled. In order to extend the engine capability in delivering mass flow and pressure at the turbine inlet, an external boost rig has been installed with the capability to control pressure, mass flow and temperature at the engine intake. In a first instance, a 1D model of the system including turbomachinery, Diesel engine and boost rig has been developed using the commercial platform Ricardo Wave. In this way, a preliminary DoE study of the entire system has been performed in order to evaluate the effects of parameters and actuators on the turbocharger operations. Additionally, the control of the rig has been tested by confirming the previous DoE study. Approaches to create turbochargers maps are shown. Last section of the paper focuses on turbine pulsations and the interpretation of efficiency calculated in experiments and simulations.
UR - http://www.scopus.com/inward/record.url?scp=84991387384&partnerID=8YFLogxK
U2 - 10.1115/GT2016-56466
DO - 10.1115/GT2016-56466
M3 - 会议稿件
AN - SCOPUS:84991387384
T3 - Proceedings of the ASME Turbo Expo
BT - Microturbines, Turbochargers and Small Turbomachines; Steam Turbines
PB - American Society of Mechanical Engineers (ASME)
T2 - ASME Turbo Expo 2016: Turbomachinery Technical Conference and Exposition, GT 2016
Y2 - 13 June 2016 through 17 June 2016
ER -